Replicate selected parts, faces, or features and arrange them in a row or grid pattern. Create new parts or modify existing parts by adding or removing material, or intersecting parts in its path. For information on creating circular patterns, see Circular Pattern. Linear pattern may also be used during an active sheet metal operation.

In the Feature toolbar:

Feature toolbar with Linear Pattern feature icon highlighted

Replicate selected parts, faces, or features and arrange them in a row or grid pattern. Create new parts or modify existing parts by adding or removing material, or intersecting parts in its path. For information on creating circular patterns, see Circular Pattern. Linear pattern may also be used during an active sheet metal operation.

The Linear pattern feature tool replicates selected parts, faces, or features and arranges them in a row or grid pattern. Create new parts or modify existing parts by adding or removing material, or intersecting parts in its path. Select the Linear pattern command on the toolbar. Then, select the parts you want to pattern. Click the Direction field in the dialog and select a direction using an edge of the part or a Mate connector (inferred or existing). Enter the Distance to offset the pattern, and adjust the Instance count to determine how many copies of the part are created. Check Centered to use the original seed part as the center of the pattern, with the same number of parts created on either side. Check Second direction to pattern the parts along a second axis. When finished, click the green checkmark to accept the new linear pattern.

  1. Click Linear pattern feature icon.

    Linear pattern feature dialog

  2. Select a Result operation type:
    • New - Create new material that results in a new part.
    • Add - Create new material and add to the existing material.
    • Remove - Take material away from existing material.
    • Intersect - Leave material only where geometry overlaps.
  3. Select the pattern type:
    • Part - To pattern an individual part
    • Feature - To pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc).
    • Face - To pattern a specific face on a specific part
  4. With focus on the Entities to pattern field, select entities to replicate into a pattern.

    When selecting Faces to pattern, the Create SelectionCreate Selection arrow icon can be useful to select related faces.

  5. Set focus in the Direction field, and then select an edge or face of the part or a Mate connector (inferred or existing) along which to place the replicated pattern entities.
  6. Enter the distance between each pattern entity, and then the number of repetitions, or Instance count (the minimum number of instances you are able to use is 1). Select a direction for the pattern in the workspace (shown below as the highlighted edge).
  7. Use Centered to make the seed instance/face/feature as the center of the pattern.

    In this case, the instance count is N instances from the seed (inclusive of the seed) in one direction and N instances from the seed (inclusive of the seed) in the other direction. With N being the number you enter in the Instance count field in the dialog:

    Example using Linear Pattern tool

  8. Select second direction to extend the pattern in a second direction; select the second direction.
  9. (Feature pattern type only) Select Reapply features to regenerate the feature for each instance (specified in Instance count), in lieu of simply recreating the initial pattern instance.
  10. Click Accept checkmark icon.

Pattern an individual part:

Example of a Linear pattern on an individual part

Pattern a sheet metal part; in this case the blue outer wall was selected:

Example of a Linear pattern on a sheet metal part

Pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc) without Reapply features selected (a faster, more lightweight feature pattern). This is not available for sheet metal.

In the following example, the initial extrude was Up to next (bringing the extrude up to the face of the surface). Without Reapply features selected, the features patterned (extrude and fillet) are patterned from the initial features and not regenerated (so the Up to next does not update for each instance of the pattern):

Example of an Up to next Extrude without Reapply features selected

Pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc) with Reapply features selected. This is available for sheet metal.

In the following example, the initial extrude was Up to next (bringing the extrude up to the face of the surface). With Reapply features selected, the features patterned (extrude and fillet) are regenerated for each instance of the pattern so Up to next is applied to each instance of the pattern.

Example of Up to next Extrude with Reapply features selected

Pattern a specific face on a specific part:

Example of patterning a specific face on a specific part

New - Create new material that results in a new part or sheet metal:

Example of creating new material that results in a new part or sheet metal

Example of creating new material that results in a new part or sheet metal

Add - Create material and add to the existing material:

Example of creating material and adding it to the existing material

Take material away; select the part to pattern, and then Remove:

Linear pattern: remove example

Leave material only where geometry overlaps; select the part to pattern, and then Intersect:

Linear pattern: intersect example

  • When selecting a face, edge, or Mate connector (inferred or existing) to set the Direction, use the Directional arrows Opposite direction arrow icon to flip the result if necessary.
  • When you select a face, edge , or Mate connector (inferred or existing) for the Direction, you are using the direction that is 'normal to' the face, edge, or mate connector.
  • When patterning a feature, you are able to select anything in the feature list, in any order. Regardless of the order selected, the features are applied in the order listed in the Feature list.
  • If you select a pattern in the Feature list, you will pattern that pattern, but not the seed. In order to get the seed included, select it as well.
  • When patterning a boolean feature (Boolean, Split, etc), you must also select the features the boolean was applied to.
  • When creating Feature patterns, all aspects of a feature are applied; for example, the end conditions in an extrude feature. (By contrast, Face patterns do not recognize these types of modifiers.)

  • If Reapply features is enabled for the feature pattern, external references will regenerate automatically on a per-instance basis.

    In a sketch, the seed sketch dimensions and constraints to the origin or default plane will not be reapplied. You can use this behavior to scope which dimensions or constraints are reapplied within a pattern:

    • You can pattern sketch features that are dimensioned or constrained to the origin or default planes and choose not reapply those dimensions and constraints.
    • You can also create explicit construction sketches along the default planes or origin when reapplying features along them.

  • If Mate connectors are Part patterned in a Part Studio, they will all be added to the Assembly when the Part Studio is inserted. If you don't see your Mate connectors when the Part Studio is inserted into the Assembly, make sure the Part is listed as the Mate connector owner entity.
  1. Tap Linear pattern tool.

    Linear pattern feature icon

    Linear pattern dialog

  2. Select the Pattern type:
    • Part - To pattern an individual part
    • Feature - To pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc.)
    • Face - To pattern a specific face on a specific part
  3. Select a Result body operation type:
    • New - Create new material that results in a new part.
    • Add - Create new material and add to the existing material.
    • Remove - Take material away from a part.
    • Intersect - Leave material only where intersections exist.
  4. Select entities (parts, features, or faces) to pattern.
  5. Specify direction of the pattern using the number pad or drag manipulator.
  6. Specify the instance count.
  7. Optionally, toggle to switch to the opposite direction.
  8. Optionally, toggle Centered to make the seed instance/face/feature as the center of the pattern.
  9. Optionally, toggle to add a second direction. If so, be sure to complete the steps for the second direction.
  10. Tap the checkmark.

Pattern an individual part.

One cylindrical part is patterned 5 times using Linear part pattern to create new material.

Example of a Linear part pattern

Pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc.)

An extrude remove feature is patterned 10 times using Linear feature pattern to remove material from the existing part.

Example of a Linear feature pattern

Example of a linear feature pattern

Pattern a specific face on a specific part.

The cylindrical face of the part is patterned 5 times using Linear face pattern to add material to the existing part.

Example of a Linear face pattern

New - Create new material that results in a new part.

Example of Linear pattern new material

Add - Create material and add to the existing material.

Example of Linear pattern add material

Take material away.

Example of Linear pattern remove

Leave material only where intersections exist.

Example of Linear pattern intersect

  1. Tap Linear pattern tool.

    Linear pattern feature icon

    Example of Linear pattern dialog

  2. Select the Pattern type:
    • Part - To pattern an individual part
    • Feature - To pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc.)
    • Face - To pattern a specific face on a specific part
  3. Select a Result body operation type:
    • New - Create new material that results in a new part.
    • Add - Create new material and add to the existing material.
    • Remove - Take material away from a part.
    • Intersect - Leave material only where intersections exist.
  4. Select entities (parts, features, or faces) to pattern.
  5. Specify direction of the pattern using the number pad or drag manipulator.
  6. Specify the instance count.
  7. Optionally, toggle to switch to the opposite direction.
  8. Optionally, toggle Centered to make the seed instance/face/feature as the center of the pattern.
  9. Optionally, toggle to add a second direction. If so, be sure to complete the steps for the second direction.
  10. Tap the checkmark.

Pattern an individual part.

One cylindrical part is patterned 5 times using Linear part pattern to create new material.

Example of Linear part pattern

Pattern a specific feature (or features) listed in the Feature list (an extrude, fillet, sweep, sketch, etc.)

An extrude remove feature is patterned 10 times using Linear feature pattern to remove material from the existing part.

Example of Linear feature pattern

Example of Linear feature pattern

Pattern a specific face on a specific part.

The cylindrical face of the part is patterned 5 times using Linear face pattern to add material to the existing part.

Example of Linear face pattern

New - Create new material that results in a new part.

Example of Linear pattern: new material

Add - Create material and add to the existing material.

Example of Linear pattern: add material

Take material away.

Example of Linear pattern: remove

Leave material only where intersections exist.

Example of Linear pattern: intersect